|
Show And Tell |
|
|
Bob,
You ROCK!!!!!!!!
Steve Kuithe
Steve (FOH Tesla) is going to give SAC a try. I put together a nice new rack PC for him and up to Sacramento for the last rehearsal with Tesla's bass player's band before going out.
Straight forward rig. Host Gigabyte H55 / i5 / 4g / c:250gb / d:1tb 3 ADAk8 HDPS-9652 4 buffers x 128 � for now. Netware router (hardwired cat5) Remote ASUS EeePC 23� Samsung BFC2000
3M Multi-touch, BCF2000 and a laptop for the SAC remote. FOH Really! The other laptop for the remote Aphexs pres. All in a DJ case.
The new SAC host. UPS, AC Conditioner, Backup PC, 4 Aphex pre-amps (40ch), 1 Aphex D/A (8ch), 1 ADA8000 for mics in/outs (8ch)
So far he is very surprised at the quality of the sound and how easy it was to operate. Right now monitors are being handled by a Crest rack mount mixer and if things work out, that will be the next to go. The goal will be to move totally into SAC for the Europe tour this winter to cut down the cost and size of touring setup. Maybe sell the Innovason!
Steve had a great time and was even more surprised how good the sound was compared to the house board that the first band used (Crest Audio). He's off to Modesto so I'll stand by the phone but I'm sure he'll be OK.
Steve at the Starline during sound check with Soulmotor.
One of the house engineers wants to cut over to SAC as of that night.
Brian Wheat (Tesla) and Soulmotor with the Host Old Host PC. New host has Aphexs in the rehearsal room
Steve at the Remote during rehearsal
Steve and I would like to thank Bob again for your support and wisdom.
Hap
Just finished an outdoor show with (4) bands. Multi-tracked two of them with SAW Studio. System ran flawless, 12 channels, 1 monitor mix. 4 scenes. Bluegrass Bands do (2) 45 minute sets, so I just saved the 1st set to a scene, then when their 2nd set came up, I just recalled from the 1st set....Done.
Mains, Subs, Front Fills
All bands commented on how clean the sound was, SAC along with 14,000 watts of PA & 2000 watts for monitors.
Thanks Bob L for a Great piece of software that allows me to do my best with ease.
Douglas Grimm Old Dominion Sound, LLC Old Dominion Music Group
Hi all,
Together with my "mixing mate" and affiliate Achim, I did a smaller festival (city festival) solely with SAC. Achim did FoH sound with his RME RayDat based SAC System and I linked up my remote laptop via Lan with a BCF2000 to do monitors. I used the SAC paragraphic EQ and the RML analyser for ringing out the monitors, that was dead easy and quick. We had an absolute insane billing to cope with. Starting with classical choirs, Irish Folk, Hip Hop, Blues Rock, Top40 up to a Death Metal (!) Band.
The weather conditions were terrible. I had 104� on stage, lots of dust (the stage was placed on a cinder pitch), than thunderstorms with heavy rain and afterwards a humidity like in a jungle! We did one day of pre-production, on that day it was also hot as hell. We had to mix 20 acts on one day with very short change over times but it all worked out great!
SAC was absolute stable and solid. But the best of it:
The sound on stage and Foh was awesome!!!
Ok, we had a nice pa rig (d&b Q-Series) but this is only one reason.
SAC did the magic concerning sound and meanwhile I'm fast enough to do six ways of monitors on the fly just with the mouse and a fader pack.
Best wishes Christian
Yesterday we did sound for a 4th of July concert and fireworks here in Greenwich, CT. We have been doing this concert for a couple of years but always with an analog board. This was the first year with SAC.
This was also the first year with the Band Shell. In the past it was always with an open wooden stage. The Tubas gave us a bit of a problem with the sound bouncing off of the roof of the metal band shell and being picked up by other mics. Not to mention the musicians moving mics after we positioned them...plus no sound check...LOL.
But...the show must go on. SAC performed perfectly. Here's a couple of pix:
Johnny Dee Ambassador Entertainment
Having finally finished and had a chance to use the new Core i5 System that I posted about earlier, I thought I'd post a follow-up for those that might be interested.
The finished weight of the 10u system was 115 pounds. So I reconfigured the system into an 8u case, removing the 2 space Drawer, Headphone Amp and UPS, which I moved into a separate rack.
The new 8u version dropped the weight to 84 lbs.. Not light, but at least managable.
I found a very nice keyboard with a built-in touchpad from Adesso.
I can operate everything from just the touchpad on the keyboard, but also added a wireless mouse with a USB receiver (logitech M510)
The final addition was the LG 21" LED HD display.
I had a problem with the built-in video not working at the proper resolution for the monitor until I realized I needed to load the Display Drivers for the Intel Graphics. Once loaded, all the proper display options for single/dual/mirrored became available.
For those wondering about the i3/i5 built-in graphics, they work very well.
The ASUS P7H55D-M EVO motherboard has built-in video support for the on-board i3/i5 graphics (HDMI / DVI / VGA) and can run any two ports simultaneously as independent/extended desktop displays.
Philip G.
Here are some pics of the SAC systems used on Sweeney Todd production at Cain Park, Cleveland Heights, OH.
FOH Position
SAC Host System
SAC Remote System
Richard B. Ingraham RBI Computers and Audio
Hi,some pics of my SAC/SS System core duo 5500 with digiface and 2 ada8k. I�m waiting for third ada8k and 5u rack...
Forum Member - Avorombri
SAC performed like a champ Friday night (at the Half Moon in Dobbs Ferry, NY).
Fujitsu LifeBook N6420 (4GB RAM), Layla24 PCMCIA, ADA8000, BCF2000. Recorded to an external 500GB OWC drive via SATA-II Express-PC card (instead of the laptop's 2nd internal drive). [Sorry, no time to take any pics. ]
I recorded to SAWStudio (via SACLink)...16 channels (actually, only 12 were used), TRS line-in (8 to Layla, 8 to ADA), from an A&H MixWizard 16-2 board's TRS direct outs. The band prefers to mix live sound in the traditional way; fortunately we went with a small-format board containing separate direct outs (so as not to have to deal with the usual Insert points).
It took a li'l getting used to running SAC with my left hand most of the time, as the rig is set up 90� to my left...I still have to do my main job of playing two keyboards and singing. I gave myself a nice monitor mix, listening through a pair of Sony MDR-7502 cans...not as g��d as the V6s I use in the studio...but smaller and lighter, so as not to l��k totally g��ky on stage.
It was gr8 having a better sound than what everyone else heard. Of course, that means that our live sound was less than stellar (to say the least). The amps were underpowered; thus, by dialing the gains and pushing the faders more and more, I wound up getting clipped signals from some of the direct outs. Bringing down the attenuators in SAC gave me the proper recording levels; however, I ended up with some clean tracks of already clipped audio. I'll do my best to polish those turds when I mix.
SAC is an amazing tool. It does a fantastic job of live mixing and as a front end to recording (e.g., to SS)...and, in my case, it also helps expose flaws and errors in the mixing process (before the signal even reaches SAC).
I've said it before, and I'll say it again...Way 2 go, MaXimum Bob!
Best regards, Mike E. Dee
I just have to share this with you.
I had a flawless night! The SAC engine ran 10 inputs for almost 4 hours @ 2x64 without a single buffer slip while simultaneously recording 8 tracks in SSL.
I had native EQ and comps on 8 channels..a reverberator and native delay on two returns...and a cross delay on one of the guitar channel inserts. FOH and Mon 1 both had native graphic EQ's inserted. 13% CPU load and no glitches!
More importantly, the mix sounded fantastic. I have never felt more in control. Afterward I overheard some people complimenting band members on the sound...especially the vocals. I heard comments like, " the vocals sounded better than usual tonight". I thought about this all the way home and I think what they meant was the vocals sounded _smoother_ than normal....which I attribute largely to your channel compresser :).
Honestly, I do not make my living running live sound but I have long lusted for the power of your EQ and Comps when I do run sound. Add in the awesome stability and flexibility of the software and it is simply unbeatable in my opinion.
BTW, the fader pack is a nice crutch I suppose, but frankly I might have touched it twice tonight. (looks cool though ;))
It is both humbling and impressive to see the scope and complexity of the Harrah's installation you shared on youtube recently...Kudos on that!... but at the opposite end, my little adventure tonight demonstrates the scaleability a SAC system offers.
I ran this whole show on a $90 Intel mobo/cpu combo I built for office work last year. This little piece of crap barely worked up a sweat. Less the RME sound card, it is a $300.00 box including the O.S. and case! Amazing. Would I try to do a show with the same machine running 16 or 24 or 32 or more inputs? Absolutely no way...But it's sure good to know when I do upgrade I can do it with peace of mind.
Thanks for listening :) Keep up the great work.
Mark
SAC now makes regular appearances in Luckenbach Texas and occasionally in the dance hall at Gruene as well as countless one-offs around the Texas hill country.
I run a rig that covers 1000 head by myself from a 12' trailer...
thnx Bob
MH
Well, last night was my first gig with SAC and I had the configuration like this:
- 24 Live Channels FOH and Monitor Mixer 1 - 7 instances of Drumagog in Live Mode - EQ, Gates, Compressors Activated - Classic Studio Reverb plugin inserted in Return 1 with Echo/Delay plugin too for voices. - No Buffer Drops at ASIO 64 Samples with RME HDSP 9652 PCI Card and 3 Behringer ADA8000 Converters
Only 16% of CPU was used. That's impressive Maybe this is not a big Live Setup but it leaves a lot of headroom for expansion of more tracks in my system, maybe in the future I'll be using SAC/SAWStudio combo too
Thanks Bob, this is a great journey!
Jesse
Just got in from today�s show, an almost horror story turned into a shining SAC triumph.
Howie Day at the Red Skelton Performing Arts Center.
Simple show...one Vocal mic, one Guitar, both extremely well preprocessed by Howie.
Conventional Monitor console (Allen& Heath) and FOH (Typhoon 4800)...when we fire it up...our normally noiseless system, which has been in that venue before, is humming...loudly.
We chase grounding & the like for 2 hours to very limited success, we get the monitor rig quite acceptable, but FOH has a loud, signal dependant, 60 Hz hum with some lovely upper harmonic content that is WAY to loud to be masked, and resistant to every effort to solve...30 minutes to doors.
I ran the SAC rig at my show the night before so the rack is still in the truck. I rush it in, pluck the snake from the FOH rig, kick the console off the workdesk, patch the computer together...20 minutes to doors.
Fire it up, bring up the inputs which are now blessedly noise free, flatten the house EQ as the rig magically no longer needs correction, add a touch of a SIR verb that I like, and everyone sighs in relief. 14 minutes to doors.
Guitar tech bops by FOH in the middle of the show, he loves the verb I chose & suggests I add a bit more of it...he calls the sound quality 'marvelous'
There were absolutely no further issues.
Until further notice, everyone can assume that even when an act specifies some other system from us, SAC will also be loaded onto the truck. Every time, without fail.
Christopher
Hi
Just want to tell my first show with SAC and SAW went very well, no problems to report.
Actually it was a very hardware mixer kind of feeling I had with SAC, it was a small setup with cello, oboe, harp and pre recorded music/efx and spoken words from an actress. I was running efx in surround.'
It was also the first time I placed the RME mixstacy on the stage with amp and a behringer ada8000 for DA conversion. This way I only had to use 2 video cables between me and the stage.
Thanks for such a good software design.
Sebastian
Bob,
I used Saw Studio and SAC a few weeks ago in a conference and blew some guys away with its potential. The speaker of the event was so amazed with what I was using that he is wanting me to travel to his church in Lake Charles Louisiana and install a SAC/Saw Studio combination in his church. When I told him what it would cost for the complete setup he says "That's less than we planned in our console alone".
This guy is an accomplished musician and singer and was so amazed at how great it sounded. He was also impressed with the ability to multi-track in and out.
Bassthumper
I am in a Band with 5 musicians and 4 singers, all 5 musicians are equipped with in ear monitors.
The problem has always been that for so many monitor mixes (5 + 1 for the floor wedges for the singers) it was not possible for the foh guy to give us exactly the mix we wanted especially given the fact that this mix should change with different songs. I came across SAC and even if its primary goal is not what I use it for, it does a heavenly job for us.... each musician has a little eeePC like computer which runs SAC remote and each musician now can mix his own monitor sound live, and even define a scene for each song. I can't describe how happy i am.
I have done too many gigs in the past without hearing what i needed to hear.
We have done our first SACified GIG this week, no problems at all.
Thank you so much Bob.
Bjoern
So I volunteered to run sound for a band I used to play with using SAC. The show was last night. SAC worked great. I loved being able to just walk around with a laptop and mix from anywhere.
Didn't use my Behringer BCF2000s, but when I use the PC rig and I am playing/running sound from stage I will definitely use them. I could see pointing and clicking while playing a live show a bit harder then running the sliders.
Audio performance was rock solid. My machine is an XP machine with 4 gig 800 mHz RAM and a Q6600 processor running at 2.4 gHz (I usually have it overclocked at 3.2gHz) with an RME HDSP 9652. CPU usage was 60% with 12 ins at 2X64 buffers - and 5 mixes. I was running the Waves Renaisannce reverb on all 5 mixes.
David
I used the SAC rig for the First Christian Church venue at the Lotus World Music Festival this weekend, it was a smashing success. I had four acts over two days with one act (Etugen Ensemble, a folk group from Mongolia) doing four performances and the others appearing in between. In that setting it was wonderful to have scene recall, allowing me to reset the entirety of the system to be optimized beyond simple channel strip settings for such wildly disparate genres of musicians. The church personnel commented repeatedly that they were so pleased our system had such wonderful sound with an amazingly tiny footprint! Previous years other companies in that venue have occupied as much as two full pews with FOH control. I had a screen on top of a 19" rack, and a chair...and had more control
Christopher
Hello everyone - I've just completed our local Country Music Festival (outdoors - 2 days) with SAC and 2 ADA8000's with a "Power Works" system as FOH.
It was an outstanding success with gracious comments from both performers and listeners.
SAC was flawless and my 2 BCF2000's gave me 16 channels of "hands on" control.
Fantastic weekend all around with the icing being the "Power Works" system far exceeding my expectations in an outdoor environment.
As backup on Saturday, I took along a H/W 16 ch mixer and extra sound system. Neither was needed even though the day was quite windy.
I left all the extras home on Sunday
Great stuff - thanks Bob.
Dennis
FYI, I just finished my second conference using SAC and SAW to record. SAC ran straight for 12 hours without a hitch.
The output for FOH and a single monitor feed was run through a small PA system for about 70 people however everyone commented on how good the sound was. Now, I have to mix it all
Bruce Callaway
So I've had SAC for a while now, but haven't really had a chance to put it through it's paces.
Today I got it all hooked up with my old laptop, Emachines 6805, Athlon xp single core, 1gb ram, nothing special at all. RME Digiface and 2 ada8000s.
So 16 channels input, Eqs and comps active on every channel, 1 Reverb, 1 Delay, 4 monitor mixes. At 1x64 I've had it running for about 6 hours, no slipped buffers and at 10% cpu usage.
I really thought I was going to have to buy a new laptop, but this setup is working like a champ so far. Thanks Bob.
John
Setup is very easy. I can create custom console setups before I get on site and it operates exactly as setup. I can transport the equivalent of several large format consoles in the trunk of my car rather than having large trucks to haul this equipment.
SAC is very intuitive. It works and functions better than an actual console. I don't have to run back and forth working over an 8 foot console. Everything is at my fingertips, including all external sound processing.
I have had multiple folks in the audience as well as performers comment at how great the sound was.
Now that my system is setup and running, no crashes. The system just simply works. Bob's software works better that advertised. I am a SAW user from back to 1992 when Bob first started out. The product just keeps getting better and better.
SAC actually works better than any piece of hardware that I have used. Much clearer sound, much easier to use. I now don't have to have consoles that are just huge slabs of steel. I now don't have to have trailer space to haul these consoles over the road from one event to the next. I have multiple consoles available in a small space, things that are not feasable with hardware.
Not even a small complaint. Even in beta, SAC has far outdone any sound console I have ever worked on.
Greg Angst Houston, Texas
This setup was for a three day music festival:
Setup and tear down of SAC could not have been easier.
The biggest adjustment to using the virtual console for me was using only a mouse for making changes... kind of like using only one hand to adjust controls on a physical console.
These mixes went out live over the regional area radio waves, plus live HD internet streaming. I received numerous positive comments from people at the festival about how good the sound was on their home and car systems. I also noticed a marked and improved difference when comparing the reference cd's I burn in realtime (from the same radio feed output) to last year's reference recordings (using an Ashly line mixer)... all other things being more or less equal.
There was no question in my mind about reliability and SAC proved flawless in this respect.
This was my very first outing with SAC as the front end mixer for my SAW PC. Three eight-hour days, ten bands worth of great music and hours of nearly flawless recording and live mixing using SAC and SAW on one PIV/2G PC and a single 19", wide-screen monitor.
With only a few days worth of testing and setting up rough templates, I was able to set up my live-to-radio mix and a second monitor mix in SAC which completely replaced both my soundcard software mixer and hardware line mixer needs from previous shows. Compensating for the festival soundman's actual channel layouts and the continual changes from band to band turned out to be one of the most painless (and rewarding) operations of the weekend thanks to SAC's Scenes and the SAW hooks. The ability to import SAC channel settings to SAW made setting up the record channel assignments go really fast and saved a lot of time since I didn't have to re-label SAW's channels.
SAC and SAW worked together perfectly! Running anywhere from 19 to 38 channels of mics from my splitter at the FOH board, SAC would operate at about 12-15% load with just the raw channels and the Levelizer patched to the radio feed output to 24-38% with one reverb and one delay on return channels, the Levelizer on the radio feed output and half or more of the inputs using EQ and Aux sends at any given moment. The load would jump significantly when using lots of the channel strip dynamics, but I ended up barely needing them (in spite of my tendency to think I might).
There are some negatives, but not so much "negatives" as observations about working within the virtual mixing console domain that make it a little difficult to work quickly. As long as I didn't "freak out", none of the mixing issues I faced were overpowering at all though. I think that with some small changes to the mixer and a lot more hands on time from me that using SAC for my needs will be a breeze, even using just the mouse and keyboard to operate it and SAW.
Dan Towey Cedar Rapids, IA
|
|
|
|